Tr brisanje

[harisfaz]

kako se moze izbrisat SVE sa TR-a? hocu da bude prazan i da ga iznova radim...tek sam ga nedavno dobio pa sam se odlucio da nesto uradim s njega???

[harisfaz]

ne zna niko???

[gnovako8]

Pozdrav ovako nemoze se brisati ali kad ga upalis ostaje mu samo kombinacije slozene znaci Bank A,B,C itd. jednostavno ili ubaci tvornicke postavke to jest PCG, i slazes po svome, a mozes ostaviti sve kako je i opet mozese slagati sve po svome , i kopirati s broja na drugi broj prepraviti ime (name) to ti je sva mudrost nema tu sta puno za cackat ako te zanima jos sta javi se

mogu ti poslat tvornicki PCG ako trebas jer bas sam kupio novog prije 5 dana.

[harisfaz]

super, hajd posalji mi taj tvornicki pcg, jer ja to nemam... imas mail adresu..

[laze]

Druze to tvornicko podesavanje imas u klavijaturu sad mi nije tu klavijatura da ti kazem gde tacno se nalazi ta opcija, ali potrazi malo nacices i samo vrati na fabricko podesavanje i to je to.

[harisfaz]

hvala puno, laze

[jager]

udjes u GLOBAL i tamo ces naci sto trazis...

Evo i uputstva kako resetovati na fabricka podesavanja za neke KORG klavijature:

Product	Preload Instructions
01/W Series	Global screen 7 Press G then E
03R/W	Global screen 5D, then select “OK”.
05R/W	Global Screen 5A, then select “OK”.
168RC	Factory data must be transmitted and returned via SysEx dump.
A1	Card Load only from a SPC0A1 (Card no longer available)
A2/A3	Hold Up and Down arrows while turning it on.
A4	Hold Bank Up and Write while turning it on. PL appears, press write again.
A5	Hold Mode Footswitch and Write while turning it on. Press Footswtich 1, F is dispayed on screen.
AD120VT	Preload - Hold down the value Up/Down button and TUNER/CANCELL. A 'P' will flash in the LED. Press the write button
AX1000G	Hold Bank footswitch and Exit button while turning it on. Press Write button to load the factory programs.
AX100G	Hold FX Select and EXIT button while turning it on. Press write button.
AX1500G	Hold down Bank footswitch EXIT button while turning it on. Then press Write button.
AX1G/B	Hold down the left arrow key and the "+ " while powering on. Then press the "+" button again.
AX300G/B	Hold Param/Value and Compare/Write while turning it on. Then Compare/Write once again.
C-Series	Disk Load C900 (CFD01P) Ci86/9600 (CID00PE )
CX-3	Hold Program 2 and 7 while turning it on.
D Series	Backup CDs
EX8000	From Tape only (Contact us via the support form for more information)
G3	Hold Bank and Write while turning it on. Release both and then press Write again.
i1/i2/i3	Disk Load (IFD01P for i3 and i2, IFD02P for i1)
I30	Disk Load (I30FD00P)
i5S/M	Disk Load (IFD00P)
iS35/40/50/B i40M	Disk Load (IFDD1006 except for iS40 and i40M which is IFDD1007)
iX300	Disk Load (IXD00P)
KAOSS Pad	N/A
KARMA	Disk Load (KMFD00P)
M1	Card Load (MPC00P) or Sysex Dump. Please contact support for information on how to send data via Sysex. (Card no longer available)
M1R/M1REX	Card Load (MPC00P, MPC0EX for EX model, no longer available)
M3R	Global screen 5D “OK”, then select "OK."
MS2000/2000R	Global screen 2D, then select "OK".
N1/N5/EX	Press Utility, select "Factory Reset" then press Enter.
N1R	Press Global, Page > to Init. Select "Factory Preload" then press Enter.
N364/N264	Disk Load (NSD3)
NX/NS5R	Enter button, then select Utility, Preset, Factory Preset, Yes.
PA80/60	Disk Load (6 Disk set available from www.korgpa.com)
Prophecy	Global screen 19, press Enter.
PX1	Metronome and Enter buttons while powering on. Then press the "+" button.
PX2	Rhythm and Enter buttons while powering on. Then press the "+" button.
PX3/PX3B	PX3: Rhythm/Aux and "+" button while powering on. Then press the Bypass/Tune button. PX3B: HBB and "+" button while powering on. Then press Bypass/Tune.
PX4/PX4B	PX4: Rhythm and UP arrow buttons while powering on. Then press Enter/Rec. PX4B: Rhythm and Up arrow buttons while powering up. Then press press Enter/Rec.
S3	Hold Stop and S1 while turning it on.
SG Rack	Global screen 7, then select "OK".
SGPROX	Program Edit mode screen 14 (Each program!)
SP500	Function screen 7.
T Series	Disk Load (TSD00PII)
Trinity Series	Disk Load (TFD00P and TFD01P)
Triton Classic/ST	Disk Load (TNFD00P and TNFD01P for Classic, Hard Drive contains preload for Studio)
Triton LE	Global mode, F8, Select "Preload" then OK
Triton Rack	Disk Load (TNRFD00P and TNRFD01P)
TR Rack	Global screen 10, then select "OK".
WS/WSEX/AD	Card Load (WPC00PI, II and III)
WSSR	Card Load (WPC00PI, II and III)
X2/X3/X3R	Disk Load (XSD00P)
X5/X5D/DR	Global Screen 5A, then select “OK”.
Z1/Z1EX	Preload screen in global mode.