Product | Preload Instructions |
01/W Series | Global screen 7 Press G then E |
03R/W | Global screen 5D, then select “OK”. |
05R/W | Global Screen 5A, then select “OK”. |
168RC | Factory data must be transmitted and returned via SysEx dump. |
A1 | Card Load only from a SPC0A1 (Card no longer available) |
A2/A3 | Hold Up and Down arrows while turning it on. |
A4 | Hold Bank Up and Write while turning it on. PL appears, press write again. |
A5 | Hold Mode Footswitch and Write while turning it on. Press Footswtich 1, F is dispayed on screen. |
AD120VT | Preload - Hold down the value Up/Down button and TUNER/CANCELL. A 'P' will flash in the LED. Press the write button |
AX1000G | Hold Bank footswitch and Exit button while turning it on. Press Write button to load the factory programs. |
AX100G | Hold FX Select and EXIT button while turning it on. Press write button. |
AX1500G | Hold down Bank footswitch EXIT button while turning it on. Then press Write button. |
AX1G/B | Hold down the left arrow key and the "+ " while powering on. Then press the "+" button again. |
AX300G/B | Hold Param/Value and Compare/Write while turning it on. Then Compare/Write once again. |
C-Series | Disk Load C900 (CFD01P) Ci86/9600 (CID00PE ) |
CX-3 | Hold Program 2 and 7 while turning it on. |
D Series | Backup CDs |
EX8000 | From Tape only (Contact us via the support form for more information)
|
G3 | Hold Bank and Write while turning it on. Release both and then press Write again. |
i1/i2/i3 | Disk Load (IFD01P for i3 and i2, IFD02P for i1) |
I30 | Disk Load (I30FD00P) |
i5S/M | Disk Load (IFD00P) |
iS35/40/50/B i40M | Disk Load (IFDD1006 except for iS40 and i40M which is IFDD1007) |
iX300 | Disk Load (IXD00P) |
KAOSS Pad | N/A |
KARMA | Disk Load (KMFD00P) |
M1 | Card Load (MPC00P) or Sysex Dump. Please contact support for information on how to send data via Sysex. (Card no longer available) |
M1R/M1REX | Card Load (MPC00P, MPC0EX for EX model, no longer available) |
M3R | Global screen 5D “OK”, then select "OK." |
MS2000/2000R | Global screen 2D, then select "OK". |
N1/N5/EX | Press Utility, select "Factory Reset" then press Enter. |
N1R | Press Global, Page > to Init. Select "Factory Preload" then press Enter. |
N364/N264 | Disk Load (NSD3) |
NX/NS5R | Enter button, then select Utility, Preset, Factory Preset, Yes. |
PA80/60 | Disk Load (6 Disk set available from www.korgpa.com) |
Prophecy | Global screen 19, press Enter. |
PX1 | Metronome and Enter buttons while powering on. Then press the "+" button. |
PX2 | Rhythm and Enter buttons while powering on. Then press the "+" button. |
PX3/PX3B | PX3: Rhythm/Aux and "+" button while powering on. Then press the Bypass/Tune button. PX3B: HBB and "+" button while powering on. Then press Bypass/Tune. |
PX4/PX4B | PX4: Rhythm and UP arrow buttons while powering on. Then press Enter/Rec. PX4B: Rhythm and Up arrow buttons while powering up. Then press press Enter/Rec. |
S3 | Hold Stop and S1 while turning it on. |
SG Rack | Global screen 7, then select "OK". |
SGPROX | Program Edit mode screen 14 (Each program!) |
SP500 | Function screen 7. |
T Series | Disk Load (TSD00PII) |
Trinity Series | Disk Load (TFD00P and TFD01P) |
Triton Classic/ST | Disk Load (TNFD00P and TNFD01P for Classic, Hard Drive contains preload for Studio) |
Triton LE | Global mode, F8, Select "Preload" then OK |
Triton Rack | Disk Load (TNRFD00P and TNRFD01P) |
TR Rack | Global screen 10, then select "OK". |
WS/WSEX/AD | Card Load (WPC00PI, II and III) |
WSSR | Card Load (WPC00PI, II and III) |
X2/X3/X3R | Disk Load (XSD00P) |
X5/X5D/DR | Global Screen 5A, then select “OK”. |
Z1/Z1EX | Preload screen in global mode. |